Create the page "Plot" on this wiki! See also the search results found.
- plot(t,x) plot(t,x)538 B (84 words) - 13:06, 11 September 2008
- This MATLAB program attempts to plot 13 cycles of a 13 Hz sinusoid. plot(t,x)449 B (75 words) - 12:24, 11 September 2008
- plot(t,y4);2 KB (239 words) - 14:00, 11 September 2008
- plot(t,x) plot(t,x)573 B (96 words) - 14:13, 11 September 2008
- plot(t,x)260 B (47 words) - 14:20, 11 September 2008
- in DT. The first plot is periodic and the second plot(n, cos(n), '.');1 KB (223 words) - 09:59, 12 September 2008
- plot(t,x)552 B (87 words) - 14:59, 11 September 2008
- plot(t,x) plot(t,x)642 B (88 words) - 15:45, 11 September 2008
- ...riodic function derived from the same cosine function would be the scatter plot that the code generates in figure and can be seen below. plot(g,n);2 KB (242 words) - 16:14, 12 September 2008
- plot(t,x);774 B (126 words) - 13:28, 12 September 2008
- plot(t,x) plot(t,x)530 B (95 words) - 16:13, 11 September 2008
- plot(t,i)808 B (131 words) - 19:18, 11 September 2008
- plot(t,x) plot(t,x)918 B (157 words) - 17:05, 11 September 2008
- After running the given MATLAB code, the following plot was produced: ...a factor of 10 (with a new value <math>T_{s}=0.007</math>), the following plot is produced:1 KB (190 words) - 17:53, 11 September 2008
- plot(t,x)314 B (57 words) - 17:50, 11 September 2008
- plot(t,x)364 B (72 words) - 18:25, 11 September 2008
- plot(t,i)1 KB (207 words) - 21:44, 11 September 2008
- plot(t,x) plot(t,x)651 B (108 words) - 21:59, 11 September 2008
- The following MATLAB code cannot plot 13 cycles of a 13Hz sinusoid because this code has too large step function. plot(t,x)344 B (58 words) - 04:10, 12 September 2008
- plot(t,x)415 B (72 words) - 04:36, 12 September 2008
- plot(ratt,rational,'b') plot(nonratt,nonrational,'r')912 B (139 words) - 07:02, 12 September 2008
- plot(t,x) plot(t,x)723 B (119 words) - 06:43, 12 September 2008
- plot(n,y,'o-'); plot(n,y,'o-')1 KB (183 words) - 07:45, 12 September 2008
- plot(t,x) plot(t,x)853 B (162 words) - 12:08, 12 September 2008
- plot(t,x) </pre>373 B (63 words) - 07:58, 12 September 2008
- %%%Make first plot plot(t,y);644 B (100 words) - 19:00, 12 September 2008
- plot(t,x)333 B (56 words) - 10:46, 12 September 2008
- plot(t,x) plot(t,x, '.');1 KB (183 words) - 09:21, 12 September 2008
- The code given by the assignment was to plot 13 cycles of a 13Hz sinusoid. plot(t,x)1 KB (178 words) - 08:34, 12 September 2008
- plot(t,x) ...f cycles. By decreasing the sampling rate we will get a much more accurate plot.411 B (73 words) - 08:43, 12 September 2008
- I will take the values from 0 to 2 seconds, repeat it every 2 seconds and plot it over three periods using the following MATLAB code: plot(t1,y1,t2,y2,t3,y3)1 KB (217 words) - 08:58, 12 September 2008
- plot(t,x)296 B (51 words) - 09:32, 12 September 2008
- %The following code attempts to plot 13 cycles of plot(t,x,'--r')718 B (119 words) - 10:41, 12 September 2008
- plot(t,x).434 B (59 words) - 10:46, 12 September 2008
- ...rtmann. I use period of 10 to create this signal to be a periodic one. The plot is shown below:310 B (57 words) - 11:05, 12 September 2008
- plot(t,x) plot(t,x)1,020 B (176 words) - 11:10, 12 September 2008
- plot(t,x)402 B (73 words) - 11:14, 12 September 2008
- plot(t,x) plot(t,x)775 B (125 words) - 17:10, 12 September 2008
- plot(x,y)"851 B (147 words) - 15:14, 12 September 2008
- An easy way to prove if a system is linear is to plot the equation representing the system and then draw a horizontal line, i.e.1 KB (197 words) - 13:16, 12 September 2008
- plot(t,x);411 B (70 words) - 12:57, 12 September 2008
- plot(t,x) plot(t,x)260 B (50 words) - 15:25, 12 September 2008
- plot(t, x);389 B (59 words) - 13:38, 12 September 2008
- ...uses Ts of 0.07, or a '''sampling rate''' of 0.07 seconds. Therefore, the plot appears to only show one cycle of the sinusoid. plot(t,x);</pre>545 B (94 words) - 14:05, 12 September 2008
- ...ere is uite large, as a result it is not getting enough points in order to plot a proper garph. plot(t,x)398 B (72 words) - 14:44, 12 September 2008
- plot(n,y) plot(n,y2)769 B (126 words) - 15:32, 12 September 2008
- plot(x,y)499 B (90 words) - 15:14, 12 September 2008
- plot(t,x) plot(t,x)380 B (70 words) - 15:31, 12 September 2008
- plot(t,x)371 B (59 words) - 15:35, 12 September 2008
- original plot: plot(t,y,'b-')649 B (104 words) - 16:13, 12 September 2008